Airsoft rifle Specna Arms SA-V26 ONE™ SAEC™ Kestrel™ ETU Red Edition

Product description The Specna Arms SA-V26 ONE™ SAEC™ Kestrel™ ETU airsoft rifleThe Kestrel V2 Basic ETU by Eshooter is an advanced ETU system featuring ease of use, durability and functionality. The Kestrel V2 Basic is programmable with trigger pulls, works with both brush and brushless motors in High Speed and High Torque configurations and increases the reliability of the replica and protects internal parts in the event of overload due to motor damage or battery drain.Functions of the Kestrel Basic system:-Pre-cocking programmable in 5 stages with a piston position learning function. (function requires a few single shots after connecting the battery for calibration)-Active Break. The replica performs a full cycle with each shot, so that no unnecessary overloads are created in the GB due to performing part of the cycle.-Locked Rotor Protection, function protects the inside of the replica in case of damage to the motor-Battery Drain Protection. Protection against battery discharge. The motor vibrates, the blue LED illuminates five times to indicate battery drain-Low/ High Voltage Protection. The module detects the number of battery cells and adjusts operation to different numbers of cells and voltages from 6V to 17V.The SA-V26 airsoft rifle by Specna Arms has been made predominantly from a uniform zinc-aluminium alloy, with the use of steel elements in the most critical points of the replica (so all screws, pins and the tactical sling mount are steel). Both the SF-type buttstock and the pistol grip, which accommodates the battery, are made of polymer polymer. The body of the replica and the RIS rail assembly have been subjected to the anodising process, which guarantees a high degree of protection of the replica against corrosion. The painting of the replica itself was done by a powder coating process, after the surface had been sandblasted. This ensures a much higher than usual abrasion resistance of the applied paint.The replica has been very well-fitted - in a way that has so far been seen almost exclusively in G&P or Classic Army manufacturers - and perfectly balanced. This ensures almost ideal manoeuvrability of the replica, while its weight is also almost imperceptible once the replica is placed against the shoulder.The replica uses the quick spring change system, the so-called Enter & Convert™. This allows for quick and efficient adjustment of the replica's power to the conditions expected on the field of play without the need for access to a workshop or a number of specialised tools - after removing the gearbox from the body of the replica, the spring replacement process itself takes literally seconds.The advantages of the Enter & Convert™ system are difficult to overestimate. In light of the prevailing trend across Europe towards legal limits on replica discharge velocity and the arrangements that exist within the environments themselves, this system guarantees the user considerable capability and a great deal of freedom. The Enter & Convert™ system allows minimal time to replace the mainspring and thus adjust the replica's discharge velocity to the area of play, so as to guarantee the ideal compromise between the effectiveness of fire control and the safety of oneself and other players.The replica has been fully adapted to work with LiPo and LiFe type batteries. The replica is ideally suited for middle-range operations.The gearbox, reinforced at the height of the cylinder head, conceals a steel spring guide that is part of the Enter & Convert™ system and set on 8-mm ball bearings and washers steel gears. The system is secured with four anti-reverse pawls. It also uses cylinder type 2 and steel cut-off lever. The replica is factory-fitted with an accurate, rotating, polymer Hop-Up chamber which allows for very precise and stable adjustment of the BB overclocking system.The Upgraded version has a number of new reinforced parts such as:- a set of reinforced steel gears- a steel spring guide- a lightweight polymer piston- a sealed aluminium piston head- a sealed metal cylinder head- a sealed metal nozzleThe Upgraded version is fitted with a 22mm dorsal RIS rail, a Keymod standard front rail assembly and an adjustable buttstock. Metal flip-up sights have been fitted to the upper RIS rail, but they can be freely replaced by any optoelectronic sighting device. Thanks to the sliding buttstock finished with an anti-slip textured footplate, it is possible to adjust the length of the replica to the shooter's build and preferences. The standard flame suppressor is mounted on a 14-mm left-hand thread, which makes it possible to attach a sound suppressor in its place.To increase the realism of the gameplay, the replica is also equipped with a operating breech release.The replica also comes with a steel hi-cap magazine that holds 300 rounds.Additional accessories shown in the photos are not included in the kit!.Package include:MagazineReplicaM90 additional springPackage exclude:The set does not include the battery nor charger